Opens in a new tab

Thermal Imaging in Explosion Proof Cameras: Oil & Gas Guide

Thermal imaging changes what an explosion proof camera can see. An optical camera depends on visible light, so it loses its usefulness at night, in dense smoke, or in fog. A thermal camera reads the infrared energy that every object emits, so it can show an overheating pump, a leaking flange, or a person on the fence line when there is no light at all. This guide explains what thermal imaging adds in hazardous areas, how thermal, optical, and bi-spectrum cameras compare, resolution and lens basics, typical oil and gas, chemical, and power applications, and how a thermal camera is housed and certified for Class I Division 1 and Zone 1.

How thermal imaging works, in plain terms

Every object above absolute zero emits infrared radiation. A thermal camera uses a sensor that responds to this long-wave infrared energy rather than to visible light, and converts it into an image where brightness or color represents relative temperature. Warmer surfaces stand out against cooler backgrounds, which is why a hot bearing, a steam leak, or a human body is visible even when the scene is pitch black.

Two points matter for industrial users. Thermal imaging is a non-contact technology, so it can observe equipment that is energized, pressurized, or unsafe to approach. And most security-grade thermal cameras show relative temperature differences rather than calibrated readings. Radiometric models that report actual temperature values exist, and if you need alarms based on measured temperature, raise that at the specification stage.

What thermal imaging adds in hazardous areas

In a classified hazardous location, the value of thermal imaging comes from three capabilities that a visible-light camera cannot provide on its own.

Detection in darkness, smoke, and fog

Thermal cameras do not need illumination. They produce a usable image at night without floodlights or infrared illuminators, which avoids adding powered lighting to a classified area. They also see through many conditions that defeat optical cameras, including smoke from a process upset, light fog, dust, and steam. Because the image is based on heat rather than reflected light, shadows, glare, and headlight flare do not produce the false alarms that analytics often generate on optical feeds.

Hot-spot and leak monitoring

Equipment that is about to fail usually gets hot first. Bearings, motor housings, electrical connections, and transformer bushings show a rising temperature signature before they trip or burn out. A fixed thermal camera pointed at critical assets gives operators a continuous view of those signatures, so maintenance can be scheduled before an unplanned shutdown. The same principle applies to leaks. A gas or liquid escaping a flange, valve packing, or pipe wall changes the surface temperature around the leak point, and that contrast is visible on a thermal image. Thermal cameras also reveal heat loss from insulation gaps on steam and process lines, which supports energy efficiency work as well as safety.

Perimeter and intrusion detection

A person on a fence line at night has a body temperature well above the surroundings for most of the year, so thermal cameras are effective for perimeter detection at tank farms, compressor stations, and remote wellsites. Thermal video paired with analytics can cover long fence runs with fewer camera positions than lit optical cameras, and it keeps working in the weather that makes visible-light surveillance unreliable.

Thermal vs optical vs bi-spectrum

Camera typeWhat it seesStrengthsLimitations
Optical (visible light)Reflected visible light, often with IR illumination at nightColor detail, reading labels and gauges, identifying people and vehicles, high resolutionNeeds light or illuminators, degraded by smoke, fog, glare, and dust
Thermal (long-wave infrared)Emitted heat energyWorks in total darkness and through smoke and fog, shows hot spots and leaks, fewer false alarms from lighting changesNo color, lower resolution than optical, cannot read text or fine detail, limited by glass and some coatings
Bi-spectrum (thermal plus optical in one housing)Both streams, often with picture-in-picture or fused outputDetection on the thermal channel, verification on the optical channel, one mounting point and one certified enclosureHigher cost per unit, more data to manage, alignment between channels must be considered

Many hazardous area installations use the two sensor types together. The thermal channel detects an anomaly or an intruder, and the optical channel confirms what it is. A bi-spectrum camera packages both in one explosion proof enclosure, which reduces the number of mounts and certified housings on the site. Where a site already has optical explosion proof cameras, adding thermal units at the critical points is a practical upgrade path.

Resolution and lens considerations

Thermal sensor resolutions are much lower than optical ones, typically a few hundred pixels on each side, and that is normal for the technology. What matters is matching resolution and lens to the task.

  • Detection, recognition, identification. A target needs a certain number of pixels across it to be detected, recognized, or identified. Longer distances need more pixels on target, which means higher resolution, a narrower lens, or both.
  • Field of view vs range. A wide lens covers a large area at short range and suits process areas. A narrow lens reaches further and suits perimeter runs and pipeline corridors. Define the scene before specifying the camera.
  • Thermal sensitivity. The ability to distinguish small temperature differences determines how clearly a camera shows subtle hot spots or a faint leak.
  • Window material. Standard glass blocks long-wave infrared. A thermal camera in an explosion proof housing needs an infrared-transmitting window that is part of the certified enclosure design, which is why a thermal explosion proof camera is not simply an optical housing with a different sensor.

Typical applications in oil and gas, chemical, and power

  • Upstream oil and gas. Perimeter and wellsite security at remote locations with no lighting, monitoring of pump jacks, compressors, and separators for overheating, and visual leak detection around wellheads and gathering lines.
  • Refining and petrochemical. Continuous watch on heat exchangers, furnaces, flare lines, and rotating equipment, plus detection of leaks at flanges and valves inside process units.
  • Chemical plants. Monitoring reactors, storage vessels, and transfer piping for abnormal temperature, as well as early fire detection in warehouses holding flammable or self-heating materials.
  • Power generation. Inspection of switchgear, transformers, bus bars, and cable terminations where loose or corroded connections show as hot spots, along with monitoring of coal handling and conveyor systems for heat build-up.

The common thread is early warning: a view of a developing problem before it becomes an alarm, a shutdown, or an incident report.

How a thermal camera is housed and certified for Class I Division 1 and Zone 1

A thermal sensor by itself is an ordinary electronic device. What makes it suitable for a hazardous location is the enclosure and the certification behind it. If you are new to the subject, the guide to understanding explosion proof cameras covers the basics of area classification. The short version follows.

In North America, locations where flammable gases or vapors are present under normal operating conditions are classified as Class I Division 1. The equivalent in the IEC and ATEX zone system is Zone 1. Equipment for these locations is typically built to the flameproof or explosion proof protection concept. The camera electronics, including the thermal core and any optical sensor, sit inside a heavy enclosure designed to contain an internal explosion and cool any escaping gases below the ignition temperature of the surrounding atmosphere. Cable entries, windows, and joints are all part of the certified design, and the thermal window must transmit infrared while meeting the enclosure’s strength and flame path requirements.

Certification is issued by a third party. In the United States, FM certification is common for Class I Division 1 equipment. ATEX covers the European Union and IECEx is the international scheme. The camera marking states the protection concept, gas group, temperature class, and equipment protection level, and the installer should confirm that it matches the site’s area classification drawing.

As a reference point, the Spectrum F-Series fixed cameras are certified Type 4X and IP66 for outdoor and washdown environments, and the F2xx family is FM certified for Class I Division 1 Groups B, C, D; Class II and III Division 1 Groups E, F, G; Zone 1 AEx db IIB+H2 Gb; and Zone 21 AEx tb IIIC Db. ATEX and IECEx certification is also available. The certifications page lists the current approvals for each family. Thermal and bi-spectrum options are available on request, and the sensor configuration is confirmed per project against the required area classification. Dome cameras with pan, tilt, and zoom are suited to process areas that need a wide covered angle, while fixed cameras are the usual choice for dedicated monitoring of a single asset or a perimeter segment.

Selection checklist

Use this list when specifying a thermal explosion proof camera or comparing proposals.

  • Area classification. Confirm the Class, Division or Zone, gas group, and temperature class from the site drawing, and match them to the camera marking.
  • Purpose of the camera. Equipment monitoring, leak detection, perimeter security, or a combination. This drives whether you need thermal only or bi-spectrum.
  • Scene and distance. Define the target size and the distance from the mounting point so the resolution and lens can be chosen correctly.
  • Environment. Outdoor, washdown, salt spray, or extreme temperature affect the ingress rating, housing material, and the need for heaters or sunshields.
  • Fixed or pan-tilt-zoom. Fixed units suit dedicated monitoring points. PTZ units cover larger areas and can be steered to an alarm.
  • Power and network. Available power at the location, cable routing through the classified area, and whether wired, PoE, or cellular connectivity is required.
  • Integration. Compatibility with the existing video management system, alarm handling, and any analytics that will run on the thermal stream.
  • Documentation and access. Request the certificate, installation instructions, and drawing package before purchase, and plan mounting positions so qualified personnel can service the enclosure with power isolated.

If you are working through this list for a specific site, you can request a quote with the area classification and the scene details, or browse the catalog at the official online store, explosionproofcamera.com.

Frequently asked questions

Can a thermal camera see through walls or glass?

No. Thermal cameras see surface temperature. Glass reflects and blocks long-wave infrared, so a thermal camera looking through a standard window shows the window, not what is behind it. This is why thermal explosion proof cameras use infrared-transmitting window materials.

Does a thermal camera detect gas leaks directly?

A standard thermal camera shows the temperature contrast that a leak creates around the escape point, which is often enough to flag a problem. Imaging the gas plume itself requires an optical gas imaging camera tuned to the absorption band of specific gases, which is a separate category of equipment.

Is thermal or bi-spectrum better for a hazardous area?

Thermal alone is sufficient when the goal is detection and monitoring. Bi-spectrum is the better choice when operators also need to verify what the thermal channel detected, read labels or gauges, or record color video for incident review, all from one certified enclosure.

Can an existing explosion proof optical camera be converted to thermal?

Not in the field. The thermal sensor, the infrared-transmitting window, and the enclosure are certified together as one assembly. Adding thermal capability means installing a camera that was built and certified as a thermal or bi-spectrum unit.

Looking for certified explosion-proof cameras?

Explore Spectrum's product line

All Spectrum cameras are independently certified to FM, ATEX, IECEx, INMETRO and PESO standards for use in classified hazardous areas worldwide.

See the full list of hazardous area certifications by product family.